Avaya Connecting BayStack AN and ANH Platforms to a Network Manuel d'utilisateur Page 84
- Page / 168
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Connecting BayStack AN and ANH Systems to a Network
5-2
This chapter provides instructions for using the ifconfig and bconfig commands
to configure Netboot and Directed Netboot. If you are not configuring the
AN/ANH yourself, you can determine the appropriate syntax for these commands
and provide the person at the router site with the exact command lines to use.
Configuring the Router Boot Source
To use Netboot, you use the bconfig command to specify that the AN/ANH
configuration file or software image resides on the network. To use Directed
Netboot, you use the
bconfig command to specify the IP address of the server and
the full pathname to the software image and configuration file.
bconfig Command Format
To configure an interface for Netboot, use the following format for the bconfig
command:
bconfig -d [image|config] network
To configure an interface for Directed Netboot, use the following format:
bconfig [image|config] network [
<TFTP host> <TFTP pathname>
]
You must use the
bconfig command twice: once to specify the location of the
software image, and again to specify the location of the configuration file.
Refer to T
able 5-1 for a complete description of the bconfig command.
Table 5-1. bconfig Command Settings
Option Description
image Indicates the router’s software image.
config Indicates the router’s configuration file.
network Indicates that the specified file (image or configuration) resides on a remote file system.
<TFTP host>
Specifies the IP address of the TFTP server. If both the software image and configuration
file are on the network, both files must reside on the same host.
<TFTP
pathname>
Specifies the complete pathname of the remote software image or configuration file.
-d Reverts to the default values for the software image or configuration file and nullifies any
previously specified IP address and pathname for the file, thus disabling Directed Netboot.
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- About This Guide 15
- Before You Begin 16
- CompuServe 17
- InfoFACTS 18
- World Wide Web 18
- How to Get Help 19
- Conventions 19
- Acronyms 20
- Chapter 1 23
- (continued) 24
- ANH Models 25
- Access Node Software 27
- Router Software 28
- Boot Configuration Options 28
- EZ-Install 29
- The Boot Process 31
- Local Boot 37
- Chapter 2 39
- Booting the Router Routinely 41
- Directed Netboot 42
- Recommendations 43
- Completing a Startup Option 44
- Chapter 3 49
- Setting Up a UNIX Boot Server 49
- Setting Up BOOTP Sockets 50
- Setting Up BOOTPD to Run 51
- Editing the bootptab File 52
- Setting Up a TFTP Server 56
- Editing the inetd.conf File 59
- Verifying the Routes 59
- Rebooting 59
- What to Do Next 60
- Chapter 4 61
- Configuring Network Booting 61
- Creating Configuration Files 62
- Preparing an Image 63
- Configuring Network Booting 67
- 2. Click on Add 68
- 4. Click on OK 69
- 71
- 72
- Enabling Router Interfaces 74
- ??? appears 78
- 1. Click on Client I/F 79
- Chapter 5 83
- Network Boot Client 83
- 84
- 84
- <next 86
- <interface> 86
- Ethernet interface 87
- <interface> 88
- Chapter 6 91
- 93
- About the N11 DCM 97
- The RMON Groups 98
- Ethernet Statistics Group 99
- HostTopN Group 100
- Matrix Group 100
- Filter Group 100
- Packet Capture Group 100
- Enabling the DCM 101
- 103
- 104
- 104
- 105
- 105
- 106
- Disabling DCM 108
- Booting DCM 108
- 2. Click on OK 111
- RMON Implementation Notes 113
- RMON Interoperability Issues 113
- RMON Memory Use 114
- Statistics Group 115
- History Group 115
- Host Group 116
- Filter and Capture Groups 118
- Appendix A 121
- Router Fails to Netboot 123
- <connector> 127
- Displaying Parameter Settings 130
- Debugging the BOOTP Server 131
- Table A-1. BOOTP Messages 132
- <IP_address> 133
- Quick Get Instructions 134
- Upgrading the Software Image 135
- Restoring a Local File System 136
- Appendix B 137
- Global Information Worksheet 139
- Router Protocol Worksheets 141
- OSPF Worksheet 142
- Wide-Area Protocol Worksheets 144
- Frame Relay Worksheet 145
- PPP Standard Worksheet 146
- Appendix C 151
- Implementation Notes 151
- 1: as the volume name 152
- Network Configuration Options 153
- Configuring a Single ANH 154
- Access Node Hub 155
- Configuring Multiple Hubs 156
- Configuring an AUI Port 157
Produits connexes et manuels pour Logiciel Avaya Connecting BayStack AN and ANH Platforms to a Network
Logiciel Avaya Configuring and Troubleshooting Bay Dial VPN (DVS) Networks Manuel d'utilisateur
(190 pages)
(190 pages)
Logiciel Avaya R4.3 Manuel d'utilisateur
(368 pages)
(368 pages)
Logiciel Avaya Read Me First: Router Software 11.02 and Site Manager 5.02 Manuel d'utilisateur
(10 pages)
(10 pages)
Logiciel Avaya B5800 Manuel d'utilisateur
(70 pages)
(70 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels