Avaya Reference for the Business Policy Switch 2000 Command Line Interface Release 1.2 Manuel d'utilisateur Page 114
- Page / 200
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
114 Chapter 3 Security
212160-A
Table 60 describes the parameters and variables for the eapol command for
modifying parameters
Table 60 eapol command for modifying parameters and variables
Parameters and variables Description
port <portnum> Specifies the ports to configure for EAPOL; enter the port number you
want.
Note: If you omit this parameter, the system uses the port number
specified when you issued the
interface command.
init Re-initiates EAP authentication.
status
authorized|unauthorizedauto
Specifies the EAP status of the port:
• authorized—port is always authorized
• unauthorized—port is always unauthorized
• auto—port authorization status depends on the result of the EAP
authentication
traffic-control in-outIin Sets the level of traffic control:
• in-out—if EAP authentication fails, both ingressing and egressing
traffic are blocked
• in—if EAP authentication fails, only ingressing traffic is blocked
re-authentication
enable|disable
Enables or disables re-authentication.
re-authentication-interval
<num>
Enter the number of seconds you want between re-authentication
attempts; range is 1 to 65535.
re-authenticate Specifies an immediate re-authentication.
quiet-interval <num> Enter the number of seconds you want between an authentication failure
and the start of a new authentication attempt; range is 1 to 65535.
transmit-interval <num> Specifies a waiting period for response from supplicant for EAP
Request/Identity packets. Enter the number of seconds you want to wait;
range is 1-65535.
supplicant-timeout <num> Specifies a waiting period for response from supplicant for all EAP
packets except EAP Request/Identity packets. Enter the number of
seconds you want to wait; range is 1-65535.
server-timeout <num> Specifies a waiting period for response from the server. Enter the number
of seconds you want to wait; range is 1-65535
max-request <num> Enter the number of times to retry sending packets to supplicant.
- Reference for the 1
- Business Policy Switch 2000 1
- Command Line Interface 1
- Release 1.2 1
- Trademarks 2
- Restricted rights legend 2
- Statement of conditions 2
- Contents 5
- Chapter 5 10
- Chapter 6 10
- Appendix A 11
- 12 Contents 12
- About this guide 19
- Before you begin 19
- Text conventions 20
- Related publications 21
- How to get help 22
- Preface 23 23
- 24 Preface 24
- Chapter 1 25
- CLI Basics 25
- Stacking compatibility 26
- Chapter 1 CLI Basics 27 27
- CLI command modes 28
- Chapter 1 CLI Basics 29 29
- 30 Chapter 1 CLI Basics 30
- Port numbering 32
- IP notation 33
- Accessing the CLI 33
- 34 Chapter 1 CLI Basics 34
- Figure 2 BPS 2000 banner 34
- Setting the CLI password 36
- Getting help 37
- Basic navigation 37
- General navigation commands 38
- Keystroke navigation 39
- BPS2000#show stack-info 46
- BPS2000#show stack-oper-mode 50
- Chapter 1 CLI Basics 51 51
- 52 Chapter 1 CLI Basics 52
- Chapter 2 53
- General CLI commands 53
- Setting the terminal 54
- Configuration Filename: 59
- Setting Telnet access 64
- Setting boot parameters 69
- Setting TFTP parameters 72
- Upgrading images 75
- Displaying interfaces 76
- Setting SNMP parameters 77
- Setting the system event log 82
- Displaying port statistics 85
- Enabling or disabling a port 87
- Setting port speed 89
- Enabling Autopology 92
- Enabling flow control 93
- Enabling rate-limiting 96
- 212160-A 100
- Chapter 3 101
- Security 101
- Using MAC address security 106
- command is: 107
- Parameters 111
- Description 111
- Using EAPOL-based security 112
- Using RADIUS authentication 115
- 118 Chapter 3 Security 118
- Chapter 4 119
- Using MLT 132
- Using port-mirroring 135
- VLANs and IGMP 139
- 140 Chapter 5 VLANs and IGMP 140
- Parameters and 141
- Chapter 5 VLANs and IGMP 145 145
- Using IGMP snooping 153
- 156 Chapter 5 VLANs and IGMP 156
- Displaying QoS parameters 158
- IP Filter Sets 163
- Resetting 168
- Configuring COPS 168
- Configuring QoS actions 180
- Configuring QoS meters 181
- Gathering QoS statistics 183
- Configuring QoS policies 184
- Reordering packets 186
- Command List 187
- 188 Appendix A Command List 188
- Appendix A Command List 189 189
- 190 Appendix A Command List 190
- Appendix A Command List 191 191
- 192 Appendix A Command List 192
- Appendix A Command List 193 193
- 194 Appendix A Command List 194
Produits connexes et manuels pour Commutateurs de réseau Avaya Reference for the Business Policy Switch 2000 Command Line Interface Release 1.2
(96 pages)
(16 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels