Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Manuel d'utilisateur Page 84
- Page / 130
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services
3-6 114070 Rev. A
You configure this type of filter by setting the Pass Through Mode parameter. This
parameter appears in several windows you use to configure BOOTP services. The
default setting is BOOTP and allows the interface to transmit only BOOTP
packets. Be sure to change the setting if you want to transmit DHCP messages.
Improving the Efficiency of Packet Relay
You can improve the efficiency of the BOOTP packet relay process by
• Specifying the addresses of BOOTP servers
• Using traffic filters
Specifying BOOTP Servers
You specify a BOOTP server by assigning a particular BOOTP server to an output
interface in the BOOTP Relay Agent Preferred Server Table window (see
F
igure 3-10). For instructions about this procedure, refer to “Specifying Servers
for BOOTP Services,” later in this chapter.
In the BOOT Relay Agent Preferred Server Table window (refer to F
igure 3-10),
you enter the IP address of the relay agent on the router and the IP address of the
target server. The router can then unicast a BOOTREQUEST packet through
normal IP services to that server.
Using Traffic Filters
For instructions on configuring traffic filters (not supported by BNX software),
refer to Configuring Traffic Filters and Protocol Prioritization. The following
example illustrates how you can use a traffic filter to enhance BOOTP operation.
Example
Consider a network segment that has two types of clients: one set that should boot
using only servers on the local network and another set that should boot from
remote servers. You could set up a traffic filter to drop any BOOTREQUEST
packets from the first set, as follows:
• Protocol: User Datagram Protocol (UDP)
• UDP destination port: BOOTP server
• User-defined field for the client hardware address in the BOOTP header: all
MAC addresses of clients in the local group
- Configuring SNMP 1
- RMON, BOOTP, DHCP 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- 114070 Rev. A 10
- About This Guide 15
- Software Suites 16
- Before You Begin 16
- Conventions 17
- Acronyms 18
- World Wide Web 21
- Customer Service FTP 21
- Support Source CD 22
- CompuServe 22
- InfoFACTS 23
- How to Get Help 23
- Configuring 25
- SNMP Implementation Notes 26
- Threshold Example 27
- 1-4 114070 Rev. A 28
- Configuring SNMP Services 29
- Enabling SNMP Services 30
- To enable IP on an interface: 31
- Click on OK 31
- 1-8 114070 Rev. A 32
- Editing SNMP Parameters 34
- 114070 Rev. A 1-11 35
- Adding an SNMP Community 38
- 114070 Rev. A 1-15 39
- 40
- Adding a Manager 41
- Editing a Manager 43
- 44
- Editing Threshold Parameters 45
- 1-22 114070 Rev. A 46
- Configuring a Threshold 47
- 49
- 51
- 52
- 53
- Editing Trap Parameters 54
- Configuring Exceptions 55
- Deleting Exceptions 58
- Chapter 2 59
- Using RMON Services 59
- 2-2 114070 Rev. A 60
- The RMON Architecture 61
- The RMON Groups 62
- Ethernet Statistics Group 63
- History Control Group 63
- Ethernet History Group 63
- Host Group 64
- HostTopN Group 64
- Matrix Group 64
- Filter Group 64
- RMON Interoperability Issues 65
- RMON Memory Use 66
- 2-10 114070 Rev. A 68
- 2-12 114070 Rev. A 70
- Enabling the DCM 71
- 2-14 114070 Rev. A 72
- Disabling the Ethernet DCM 75
- Activating the Ethernet DCM 75
- Booting the Ethernet DCM 76
- 114070 Rev. A 2-19 77
- Chapter 3 79
- Configuring BOOTP Services 79
- 3-2 114070 Rev. A 80
- Configuring BOOTP Services 81
- 3-4 114070 Rev. A 82
- 3-6 114070 Rev. A 84
- Enabling BOOTP Services 85
- Editing BOOTP Parameters 87
- 114070 Rev. A 3-13 91
- 3-16 114070 Rev. A 94
- 2. Click on Delete 94
- 114070 Rev. A 3-17 95
- 3-18 114070 Rev. A 96
- 4. Click on OK 96
- 114070 Rev. A 3-19 97
- 100
- Deleting BOOTP Globally 101
- Chapter 4 103
- Configuring DHCP Services 103
- 4-2 114070 Rev. A 104
- Configuring DHCP Services 105
- 4-4 114070 Rev. A 106
- Implementation Notes 108
- Enabling DHCP Services 108
- Enabling DHCP on an Interface 108
- Editing DHCP Parameters 109
- Deleting DHCP Globally 110
- Chapter 5 111
- Configuring RARP Services 111
- Enabling RARP Services 112
- Enabling RARP on an Interface 113
- Editing RARP Parameters 114
- 114070 Rev. A 5-5 115
- 116
- 114070 Rev. A 5-7 117
- Disabling RARP Globally 118
- Deleting RARP Globally 119
- Appendix A 121
- Default Parameter Settings 121
- A-2 114070 Rev. A 122
- BOOTP and DHCP Parameters 123
- RARP Parameters 124
- 114070 Rev. A Index-1 125
- 114070 Rev. A Index-3 127
- 114070 Rev. A Index-5 129
Produits connexes et manuels pour Manuels des logiciels Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services
(76 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels