Avaya S8710 Manuel d'utilisateur Page 90
- Page / 96
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
B Troubleshooting an installation
Configuring the media server hardware
90 Installing and Configuring the Avaya S8700 or S8710 Media Server
June 2004
Configuring the media server hardware
Problem Solution
Cannot log into UPS subagent - Make sure the SNMP Subagent is installed in the UPS.
- Make sure you are connected to the correct Ethernet port.
- Make sure you have the correct login ID and password. See the
user’s guide that comes with the SNMP Subagent.
- Make sure the network card on the laptop is configured correctly.
Cannot log into Ethernet switch - Make sure you are connected to the correct Ethernet port. (One
Ethernet switch, it is the port marked Console)
- Make sure you have the correct login ID and password. See the
user’s guide that comes with the Ethernet switch.
- Make sure the network card on the laptop is configured correctly.
Cannot log into media server - Make sure you are connected to the Services Ethernet port. (Default
is port 2 [Eth1] on the back of the server).
- Make sure you are using a crossconnect cable between the laptop
and server.
- Make sure the ARP cache is cleared on the laptop. In an MS-DOS
window, type
arp -d 192.11.13.6 and press Enter.
- Make sure you have connectivity. In an MS-DOS window, type
ping 192.11.13.6 and type Enter.
- Make sure the NIC on the laptop is configured correctly.
Cannot access Avaya Installation Wizard - Make sure you are plugged into the Services port (2 [Eth1])
- Make sure you are using the correct IP address: 192.11.13.6
- Make sure you are using the correct login and password.
- Make sure the NIC on the laptop is configured correctly.
Cannot use SAT commands - Make sure you are using the correct IP address: 192.11.13.6 and
port (5023)
- Make sure you are using the correct login and password.
- Make sure you are logged onto the active server.
Cannot ping out to customer’s network - Make sure that in the LAN security settings that "output from
server" for icmp is enabled.
Cannot ping media server from
customer’s network
- Make sure that in the LAN security settings that "input to server" for
icmp is enabled.
Cannot access media server remotely - Make sure in the LAN security settings that "input to server" are
checked for telnet (Linux commands), https (Web access), and def-sat
(SAT commands access). The LAN security settings can be changed
on the Web interface with a direct connection to the media server.
LED display on IPSI is flashing - IPSI LED has not been programmed with switch and location
(DHCP)
- IPSI LED has not had an IP address assigned to it (static IP
addressing)
Cannot access IPSI for static addressing - Make sure you are plugged into the Services (top) port on the IPSI.
- Make sure the ARP cache is cleared on the laptop. In an MS-DOS
command window, type
arp -d 192.11.13.6 and press Enter.
- $YD\D6RU60HGLD 1
- 830 nm - 860 nm -1.5 dBm 3
- 1270 nm - 1360 nm -3.0 dBm 3
- 1540 nm - 1570 nm 5.0 dBm 3
- Contents 5
- 3 Translating the IPSIs 43 6
- Index 93 8
- Conventions 10
- About This Documentation 12
- Message Transfer? field 12
- Related resources 13
- Technical assistance 14
- Trademarks 14
- Sending us comments 14
- 1 Introduction 15
- Pre-installation information 16
- 1Introduction 17
- Equipment specifications 18
- Required hardware 20
- Documentation 21
- Figure notes 23
- Connecting the USB modems 24
- June 2004 26
- • IP address (1 for each UPS) 28
- • Subnet mask 28
- SECURITY ALERT: 29
- Single control network 30
- Duplicated control network 30
- Configuring the media server 33
- Powering up the media server 34
- Accessing the media server 34
- Setting up Telnet 34
- CAUTION: 35
- Configuring the modem 39
- AT%T19,0,10 40
- 5 Close the browser 41
- 3 Translating the IPSIs 43
- Inputing translations 44
- Resetting the media server 44
- Adding media gateways 44
- Administering the IPSIs 45
- 3 Repeat for each IPSI 48
- 4 Connecting to the IPSIs 49
- Using DHCP addressing 50
- Using static addressing 51
- Enabling control of IPSIs 55
- Verifying license status 56
- Completing the installation 57
- Verifying date and time 59
- Resolving alarms 60
- 4 Click Submit Changes 61
- Telneting to media server 65
- Enabling alarms 65
- Registering the system 66
- Testing the license file 70
- LED indicators 71
- S8710 Media Server LEDs 74
- Avaya Ethernet switch LEDs 76
- IPSI LEDs 77
- A Accessing the media server 81
- Network configuration 87
- Browser settings 88
Produits connexes et manuels pour Systèmes de cinéma à domicile Avaya S8710
(768 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.405 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels