Avaya Configuring ATM Services Manuel d'utilisateur Page 248
- Page / 310
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring ATM Services
C-4
A router that needs the ATM address of a host on the LIS sends an ATMARP
request to the server. The server returns a response containing the address. The
router extracts the ATM address of the host from the response and opens an SVC
directly to the host via ATM UNI signaling.
If the server does not have an entry for the requested IP address, it returns a
negative acknowledgment, signifying that the destination is unreachable.
Configuring an ATMARP Client and an ATMARP Server
Site Manager allows you to
• Specify SVC as the virtual circuit type. All network devices on a LIS must be
connected by SVCs.
• Specify an encapsulation type for messages transmitted over the circuit. (RFC
1577 defines LLC/SNAP as the encapsulation type for ATMARP.)
• Add IP and IP routing protocols to the circuit.
• Configure ATMARP to run on the router as a client or a server.
To configure an ATMARP client or server:
1. In the Configuration Manager window, select an ATM link module, click
on a connector, and name the circuit.
The Initial ATM Signaling Config window opens (Figure C-3).
Note: For full compatibility with RFC 1577, you may have to specify an MTU
size of 9188 bytes. Refer to Configuring Line Services for additional
information about setting the MTU size.
- Configuring ATM Services 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- About This Guide 19
- CompuServe 21
- InfoFACTS 21
- How to Get Help 22
- Conventions 22
- Acronyms 23
- Chapter 1 27
- ATM Overview 27
- Cell Header 28
- Cell Information Field 29
- ATM Layers 30
- Data Transmission 33
- ATM DXI versus ATM 34
- For More Information 35
- Chapter 2 37
- ATM DXI Support 38
- AAL Sublayer Support 39
- ATM DXI LMI Support 40
- ATM DXI Error Checking 40
- ATM DXI Implementation Notes 41
- ATM DXI Modes of Operation 42
- Group Access Mode 44
- Direct Access Mode 45
- Hybrid Access Mode 45
- Site A Site B 47
- Multipath Support 48
- Chapter 3 51
- Enabling ATM DXI Service 51
- Click on Add 55
- Chapter 4 59
- Editing ATM DXI Parameters 59
- 64
- Configuring PVCs 65
- 73
- 74
- Deleting PVCs 82
- Chapter 5 85
- ATM Support 86
- Multiprotocol Encapsulation 87
- ARP and Inverse ARP Support 88
- LAN Emulation 88
- ATM Signaling 89
- ATM Error Checking 90
- ATM Implementation Notes 91
- Hybrid Access 94
- SVC Access Methods 96
- ATM Traffic Parameters 96
- Converting Mb/s to Cells/s 97
- Variable Bit Rate 98
- Available Bit Rate 98
- Configuring ATM Services 100
- Maximum Burst Size 101
- Chapter 6 103
- Enabling ATM Service 103
- Enabling Overview 104
- Adding an ATM Circuit 104
- Click on OK 105
- Adding a Service Record 109
- Figure 6-4) 110
- 2. Click on Add 111
- 2. Click on OK 116
- Adding PVCs 118
- Chapter 7 121
- ATM Editing Basics 121
- Accessing ATM Windows 122
- Configuring 124
- Line Services 124
- Selecting Service Attributes 126
- Selecting Line Attributes 131
- Selecting ATM Signaling 132
- Selecting SAAL Attributes 134
- Selecting ILMI Attributes 136
- Assigning Data Encapsulation 138
- LANE 802.3 139
- LLC/SNAP Encapsulation 139
- Encapsulation Rules for PVCs 140
- Using ATM Protocol Menus 141
- Deleting Individual PVCs 149
- Click on PVC 150
- Click on Delete 150
- Site Manager deletes the PVC 150
- Deleting Individual SVCs 151
- Deleting ATM from the Router 154
- Chapter 8 155
- Editing Service Attributes 156
- Adding Service Records 157
- Figure 8-1) 158
- 162
- 163
- Adding or Copying PVCs 167
- Copying a PVC 169
- 7. Click on OK 170
- Editing PVC Parameters 172
- 8. Click on OK 174
- 183
- 183
- Chapter 9 195
- Click on Apply 210
- 216
- Editing ILMI Attributes 220
- Appendix A 231
- Appendix B 239
- ATM LAN Emulation Overview 239
- LAN Emulation Components 240
- LAN Emulation Server 241
- Broadcast and Unknown Server 241
- Initial State 243
- LECS Connect State 243
- Configure State 243
- Join State 243
- Initial Registration State 244
- BUS Connect State 244
- Operational State 244
- Appendix C 245
- ATM Address Resolution 247
- Adding an Adjacent Host 256
- 258
- Deleting an Adjacent Host 260
- Appendix D 265
- Sample ATM Network 265
- Hardware Devices 267
- Role of the CMS 269
- Role of the MCS 269
- Role of the ATM NMA 270
- Click on Service Attributes 271
- 10. Click on OK 274
- Appendix E 275
- ATM Sample Log 275
Produits connexes et manuels pour Mise en réseau Avaya Configuring ATM Services
Mise en réseau Avaya IPv6 Manuel d'utilisateur
(162 pages)
(162 pages)
Mise en réseau Avaya L2TP Manuel d'utilisateur
(114 pages)
(114 pages)
Mise en réseau Avaya Integrated Management Release 3.0 Standard Management Manuel d'utilisateur
(52 pages)
(52 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels