Avaya Configuring ATM Services Manuel d'utilisateur Page 188
- Page / 310
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring ATM Services
8-34
Parameter: Expected LE_ARP Response Time
Default: 3
Range: 1 to 30
Function: Defines the amount of time (in seconds) that the LAN emulation client
expects an ARP request and ARP response cycle to take. The LAN
emulation client uses this value during retries and verifications.
Instructions: Accept the default, 3, or enter a value from 1 to 30.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.5.20.1.1.17
Parameter: Flush Timeout
Default: 4
Range: 1 to 4
Function: Defines the amount of time (in seconds) that the LAN emulation client
waits to receive a flush response (after sending a flush request) before it
takes recovery action by switching back to the BUS.
Instructions: Accept the default, 4, or enter a value from 1 to 4.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.5.20.1.1.18
Parameter: Path Switching Delay
Default: 6
Range: 1 to 8
Function: Defines the amount of time (in seconds) that the LAN emulation client
waits after sending a frame over an old VCC before it switches to a new
VCC (this applies to multicast and data direct VCCs). You can use this
parameter to bypass the Flush protocol (that is, when you disable the
Flush Protocol parameter, the data for a specific MAC address
automatically begins flowing over a new VC when the Path Switching
Delay time elapses).
Instructions: Accept the default, 6, or enter a value from 1 to 8.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.5.20.1.1.19
- Configuring ATM Services 1
- Bay Networks Software License 3
- (continued) 4
- Contents 5
- About This Guide 19
- CompuServe 21
- InfoFACTS 21
- How to Get Help 22
- Conventions 22
- Acronyms 23
- Chapter 1 27
- ATM Overview 27
- Cell Header 28
- Cell Information Field 29
- ATM Layers 30
- Data Transmission 33
- ATM DXI versus ATM 34
- For More Information 35
- Chapter 2 37
- ATM DXI Support 38
- AAL Sublayer Support 39
- ATM DXI LMI Support 40
- ATM DXI Error Checking 40
- ATM DXI Implementation Notes 41
- ATM DXI Modes of Operation 42
- Group Access Mode 44
- Direct Access Mode 45
- Hybrid Access Mode 45
- Site A Site B 47
- Multipath Support 48
- Chapter 3 51
- Enabling ATM DXI Service 51
- Click on Add 55
- Chapter 4 59
- Editing ATM DXI Parameters 59
- 64
- Configuring PVCs 65
- 73
- 74
- Deleting PVCs 82
- Chapter 5 85
- ATM Support 86
- Multiprotocol Encapsulation 87
- ARP and Inverse ARP Support 88
- LAN Emulation 88
- ATM Signaling 89
- ATM Error Checking 90
- ATM Implementation Notes 91
- Hybrid Access 94
- SVC Access Methods 96
- ATM Traffic Parameters 96
- Converting Mb/s to Cells/s 97
- Variable Bit Rate 98
- Available Bit Rate 98
- Configuring ATM Services 100
- Maximum Burst Size 101
- Chapter 6 103
- Enabling ATM Service 103
- Enabling Overview 104
- Adding an ATM Circuit 104
- Click on OK 105
- Adding a Service Record 109
- Figure 6-4) 110
- 2. Click on Add 111
- 2. Click on OK 116
- Adding PVCs 118
- Chapter 7 121
- ATM Editing Basics 121
- Accessing ATM Windows 122
- Configuring 124
- Line Services 124
- Selecting Service Attributes 126
- Selecting Line Attributes 131
- Selecting ATM Signaling 132
- Selecting SAAL Attributes 134
- Selecting ILMI Attributes 136
- Assigning Data Encapsulation 138
- LANE 802.3 139
- LLC/SNAP Encapsulation 139
- Encapsulation Rules for PVCs 140
- Using ATM Protocol Menus 141
- Deleting Individual PVCs 149
- Click on PVC 150
- Click on Delete 150
- Site Manager deletes the PVC 150
- Deleting Individual SVCs 151
- Deleting ATM from the Router 154
- Chapter 8 155
- Editing Service Attributes 156
- Adding Service Records 157
- Figure 8-1) 158
- 162
- 163
- Adding or Copying PVCs 167
- Copying a PVC 169
- 7. Click on OK 170
- Editing PVC Parameters 172
- 8. Click on OK 174
- 183
- 183
- Chapter 9 195
- Click on Apply 210
- 216
- Editing ILMI Attributes 220
- Appendix A 231
- Appendix B 239
- ATM LAN Emulation Overview 239
- LAN Emulation Components 240
- LAN Emulation Server 241
- Broadcast and Unknown Server 241
- Initial State 243
- LECS Connect State 243
- Configure State 243
- Join State 243
- Initial Registration State 244
- BUS Connect State 244
- Operational State 244
- Appendix C 245
- ATM Address Resolution 247
- Adding an Adjacent Host 256
- 258
- Deleting an Adjacent Host 260
- Appendix D 265
- Sample ATM Network 265
- Hardware Devices 267
- Role of the CMS 269
- Role of the MCS 269
- Role of the ATM NMA 270
- Click on Service Attributes 271
- 10. Click on OK 274
- Appendix E 275
- ATM Sample Log 275
Produits connexes et manuels pour Mise en réseau Avaya Configuring ATM Services
Mise en réseau Avaya IPv6 Manuel d'utilisateur
(162 pages)
(162 pages)
Mise en réseau Avaya L2TP Manuel d'utilisateur
(114 pages)
(114 pages)
Mise en réseau Avaya Integrated Management Release 3.0 Standard Management Manuel d'utilisateur
(52 pages)
(52 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels