Avaya Configuring Frame Relay Services Manuel d'utilisateur Page 218
- Page / 240
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring Frame Relay Services
C-10
117376-C Rev. 00
The output includes the following information:
congestion [-dlci
<dlci>
] [interface
<name>
] [-service
<name>
]
[-state {forwarding
|
throttling
|
shutdown}]
Displays information about the congestion state and the configuration of frame
relay VCs. This command allows for the following command filters and filter
arguments:
Interface The interface on which the frame relay circuit resides.
DLCI Name of the VC associated with this circuit.
CIR Committed information rate.
Committed Burst The maximum number of bits that the router can transmit over a
specified time interval (B
c).
Excess Burst The maximum number of extra bits the router attempts to send
when there is no congestion (B
e).
Config Mode Indicates whether the circuit is configured to use traffic shaping.
Congestion State Status of traffic; options are:
•
forwarding --
sending traffic at up to the maximum rate allowed
on the PVC.
•
congested
-- the PVC is not transmitting.
•
throttling
-- the PVC is throttling back to the CIR rate.
-dlci
<dlci>
Displays only frame relay VCs with the specified DLCI.
-interface
<name>
Displays only frame relay VCs configured on the specified
interface.
-service
<name>
Displays only frame relay VCs on the specified service.
-state
{
forwarding |
throttling | shutdown
}
Displays information about VCs in the following states:
•
forwarding
-- shows only frame relay VCs that are
forwarding.
•
throttling
-- shows only frame relay VCs that are
throttling.
•
shutdown
-- shows only frame relay VCs that are shut
down.
- Configuring 1
- Frame Relay Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117376-C Rev. 00 10
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 26
- Configuring an SVC 27
- Chapter 2 31
- Frame Relay Overview 31
- Introduction to Frame Relay 32
- Permanent Virtual Circuits 33
- Switched Virtual Circuits 33
- PVC and SVC Comparison 34
- Frame Relay Packets 35
- . Note, however 36
- Management Protocols 37
- BYS0037A 38
- LAPF Operational States 39
- SVC Signaling 41
- Call Setup 42
- Message Processing 43
- Frame Relay Service Records 44
- Frame Relay Access Modes 45
- Direct Access Mode 46
- Hybrid Access Mode 46
- Source Routing 48
- RFC 1490 48
- Address Resolution for PVCs 48
- Address Resolution for SVCs 49
- Traffic Control 50
- Data Compression 51
- Data Encryption 51
- Protocol Prioritization 51
- Traffic Shaping 53
- Quality of Service 55
- Traffic Shaping for SVCs 57
- Incoming 59
- Outgoing 59
- CIR Configuration Guidelines 60
- WCP and CIR Enforcement 60
- Oversubscribing the Interface 62
- X.213 Priority for SVCs 64
- Inactivity Timing for SVCs 64
- Multiline for PVCs 65
- PVC Pass-Through 67
- Frame Relay Dial Services 68
- Caution: 71
- Selecting a Management Type 72
- Selecting a DLCI Address Type 74
- Selecting Address Length 74
- Monitoring the Connection 76
- Polling Interval 77
- Full Enquiry Interval 77
- Customizing PVCs 81
- To delete PVCs: 87
- To move PVCs: 87
- Enabling Multicast 88
- Configuring PVC Pass-Through 90
- <integer> 100
- Enabling Compression for PVCs 102
- Using the BCC 103
- Using Site Manager 103
- Customizing SVCs 105
- For example: 107
- To delete service records: 107
- Call Screening and Blocking 108
- Disabling SVCs 112
- Disconnecting Active SVCs 114
- Setup Timer 121
- <value> 126
- (continued) 128
- Congestion Control 129
- Congestion Timer 130
- Congestion Counter 130
- Congestion Method 131
- To enable congestion control 134
- To enable traffic shaping 139
- To disable compression: 141
- To set X.213 priority value 143
- Deleting Frame Relay 144
- Customizing Frame Relay 145
- Appendix A 147
- Site Manager Parameters 147
- Figure A-2 148
- SVC LAPF Parameters 157
- SVC Signaling Parameters 163
- Parameters for PVCs 168
- PVC Service Record Parameters 172
- SVC Service Record Parameters 180
- SVC Options Parameters 186
- WHERE DOES THIS PARAMETER GO? 200
- Appendix B 201
- Table B-1. RIP Parameters 202
- Appendix C 209
- Monitoring Frame Relay Using 209
- BCC show Commands 209
- Commands for Frame Relay 210
- <option> 212
- <dlci> 215
- <name> 215
- ] [-service 216
- <multiline_name> 223
- <name> 228
Produits connexes et manuels pour Mise en réseau Avaya Configuring Frame Relay Services
Mise en réseau Avaya Configuring Ethernet, FDDI, and Token Ring Services Manuel d'utilisateur
(156 pages)
(156 pages)
Mise en réseau Avaya MultiVantage Configuration Manager Release 1.1 Guide de configuration
(44 pages)
(44 pages)
Mise en réseau Avaya VoIP Monitoring Manager Release 3.0 Configuration Manuel d'utilisateur
(44 pages)
(44 pages)
Mise en réseau Avaya X.25 Manuel d'utilisateur
(198 pages)
(198 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels