Avaya Configuring Frame Relay Services Manuel d'utilisateur Page 173
- Page / 240
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Site Manager Parameters
117376-C Rev. 00
A-27
To access the FR PVC List for Service window:
Site Manager Procedure
You do this System responds
1. Click on the
Protocols
menu in the
Configuration Manager menu bar.
The Protocols menu opens.
2. Click on
Frame Relay
. The Frame Relay menu opens.
3. Click on
Services
. The Frame Relay Service List window
opens.
4. Click on the
PVCs
button. The FR PVC List for Service window
opens.
Parameter: Circuit State Set
Path: Configuration Manager > Protocols > Frame Relay > Services > PVCs
Default: Active
Options: Invalid
|
Active
|
Inactive
Function: Specifies the state of the PVC.
Instructions: To indicate to a frame relay switch that the PVC is available for use, set to
Active. To indicate that the PVC is configured, but not available for use (for
example, before your switch provider actually activates the PVC), set to
Inactive. If the PVC is configured, but the switch is unaware of it, choose
Invalid.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.9.2.1.7
Parameter: Multicast
Path: Configuration Manager > Protocols > Frame Relay > Services > PVCs
Default: Unicast
Options: Unicast
|
Multicast
Function: Indicates whether this PVC is multicast or unicast.
Instructions: Set to Unicast or Multicast according to PVC type, as the frame relay switch
provider instructs.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.9.2.1.19
- Configuring 1
- Frame Relay Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117376-C Rev. 00 10
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 26
- Configuring an SVC 27
- Chapter 2 31
- Frame Relay Overview 31
- Introduction to Frame Relay 32
- Permanent Virtual Circuits 33
- Switched Virtual Circuits 33
- PVC and SVC Comparison 34
- Frame Relay Packets 35
- . Note, however 36
- Management Protocols 37
- BYS0037A 38
- LAPF Operational States 39
- SVC Signaling 41
- Call Setup 42
- Message Processing 43
- Frame Relay Service Records 44
- Frame Relay Access Modes 45
- Direct Access Mode 46
- Hybrid Access Mode 46
- Source Routing 48
- RFC 1490 48
- Address Resolution for PVCs 48
- Address Resolution for SVCs 49
- Traffic Control 50
- Data Compression 51
- Data Encryption 51
- Protocol Prioritization 51
- Traffic Shaping 53
- Quality of Service 55
- Traffic Shaping for SVCs 57
- Incoming 59
- Outgoing 59
- CIR Configuration Guidelines 60
- WCP and CIR Enforcement 60
- Oversubscribing the Interface 62
- X.213 Priority for SVCs 64
- Inactivity Timing for SVCs 64
- Multiline for PVCs 65
- PVC Pass-Through 67
- Frame Relay Dial Services 68
- Caution: 71
- Selecting a Management Type 72
- Selecting a DLCI Address Type 74
- Selecting Address Length 74
- Monitoring the Connection 76
- Polling Interval 77
- Full Enquiry Interval 77
- Customizing PVCs 81
- To delete PVCs: 87
- To move PVCs: 87
- Enabling Multicast 88
- Configuring PVC Pass-Through 90
- <integer> 100
- Enabling Compression for PVCs 102
- Using the BCC 103
- Using Site Manager 103
- Customizing SVCs 105
- For example: 107
- To delete service records: 107
- Call Screening and Blocking 108
- Disabling SVCs 112
- Disconnecting Active SVCs 114
- Setup Timer 121
- <value> 126
- (continued) 128
- Congestion Control 129
- Congestion Timer 130
- Congestion Counter 130
- Congestion Method 131
- To enable congestion control 134
- To enable traffic shaping 139
- To disable compression: 141
- To set X.213 priority value 143
- Deleting Frame Relay 144
- Customizing Frame Relay 145
- Appendix A 147
- Site Manager Parameters 147
- Figure A-2 148
- SVC LAPF Parameters 157
- SVC Signaling Parameters 163
- Parameters for PVCs 168
- PVC Service Record Parameters 172
- SVC Service Record Parameters 180
- SVC Options Parameters 186
- WHERE DOES THIS PARAMETER GO? 200
- Appendix B 201
- Table B-1. RIP Parameters 202
- Appendix C 209
- Monitoring Frame Relay Using 209
- BCC show Commands 209
- Commands for Frame Relay 210
- <option> 212
- <dlci> 215
- <name> 215
- ] [-service 216
- <multiline_name> 223
- <name> 228
Produits connexes et manuels pour Mise en réseau Avaya Configuring Frame Relay Services
Mise en réseau Avaya Configuring Ethernet, FDDI, and Token Ring Services Manuel d'utilisateur
(156 pages)
(156 pages)
Mise en réseau Avaya MultiVantage Configuration Manager Release 1.1 Guide de configuration
(44 pages)
(44 pages)
Mise en réseau Avaya VoIP Monitoring Manager Release 3.0 Configuration Manuel d'utilisateur
(44 pages)
(44 pages)
Mise en réseau Avaya X.25 Manuel d'utilisateur
(198 pages)
(198 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels