Avaya BayStack ARN Routers Manuel d'utilisateur Page 60
- Page / 162
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installing and Operating BayStack ARN Routers
2-4
114200-C Rev 00
Starting the ARN for the First Time
The ARN factory defaults are set to find the image file and configuration file from
the following locations:
• Image file -- on the local PCMCIA flash memory card
• Configuration file -- over the network
These default settings work with the default EZ-Install procedure.
The first time you power on an ARN, the router steps through its diagnostic tests
and then attempts to boot over all of its serial (COM) interfaces using EZ-Install.
If your network administrator has configured the network for the EZ-Install
procedure, the router boots using its local image and obtains its configuration file
over the network. Your network administrator can then connect to the ARN and
manage it remotely. For more information, refer to the next section, “
Using
EZ-Install.”
If your network administrator does not configure the network for EZ-Install, the
ARN cannot obtain its configuration file from the network, and the EZ-Install
procedure fails. The ARN then attempts to boot locally with the configuration file
that resides on its flash memory card. Refer to “
Using Netboot, Directed Netboot,
or Local Boot” for more information.
If both the EZ-Install and local boot attempts fail, the EZ-Install and local boot
processes repeat until one of the following occurs:
• The ARN boots successfully.
• You interrupt the boot process to enter the ARN monitor.
• You turn off the ARN.
The following sections describe how to use each of the different boot options for
the ARN.
Note:
Coordinate the initial startup of the ARN with your network
administrator. To determine which software configuration option is best for
your site and for instructions on setting up a boot server, the network
administrator can refer to Configuring BayStack Remote Access.
- Installing and Operating 1
- BayStack ARN Routers 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 3
- European Requirements Only 3
- Canada Requirements Only 4
- Contents 7
- 114200-C Rev 00 10
- About This Guide 17
- Conventions 18
- Acronyms 19
- Bay Networks Customer Service 21
- How to Get Help 21
- Chapter 1 23
- Installing the ARN 23
- Preparing to Install the ARN 24
- Additional Equipment 26
- Rack-Mounting the ARN 28
- Cagenut Screw 30
- (4 Places) 30
- Caution: 33
- and Figure 1-7 34
- BayStack Advanced Remote Node 36
- ARN0067A 38
- Reg. Number 4P8USA-31445-DE-N 42
- Connecting a PC Console 47
- Connecting a Terminal Console 49
- Console cable plus 50
- Connecting a Console Modem 51
- Connecting the Power Cable 54
- 100-240~ 55
- Where to Go Next 56
- Chapter 2 57
- Starting the ARN 57
- Using EZ-Install 61
- Interrupting the Boot Process 62
- Continuing with Netboot 64
- $) appears 70
- Chapter 3 73
- Operating the ARN 73
- Expansion Module LEDs 77
- Adapter Module LEDs 78
- Table 3-10. ISDN BRI LEDs 79
- Table 3-13. X.25 PAD LEDs 80
- Table 3-14. V.34 Modem LEDs 81
- Table 3-15. Boot Status LEDs 82
- Protecting Memory Card Files 86
- Chapter 4 89
- Powering Down 90
- Removing the Filler Panel 91
- Removing an Adapter Module 93
- Installing an Adapter Module 94
- What to Do Next 96
- Appendix A 97
- Directed Netboot 97
- Using the ifconfig Command 98
- <IP address> 99
- <interface> 99
- <interface> 100
- <next hop address> 100
- <next hop 101
- <port #> 102
- <TFTP host> 103
- <TFTP path> 103
- Verifying Your Configuration 104
- Appendix B 107
- Before You Run Quick-Start 108
- Quick-Start procedure 109
- Filling Out the Worksheets 110
- (continued) 111
- (continued) 112
- Appendix C 125
- ARN Technical Specifications 125
- Electrical Specifications 126
- Environmental Specifications 126
- Configuring Dial Services 129
- CAB0107A 130
- Table C-4 131
- Token Ring STP Interface 132
- Token Ring UTP Interface 133
- Serial Interfaces 133
- CAB0108A 134
- ISDN BRI U Interface 135
- ISDN BRI S/T Interface 136
- 56/64K DSU/CSU Interface 137
- FT1/T1 DSU/CSU Connections 137
- 12345678 138
- X.25 PAD Connections 139
- Local Console Connections 140
- Service Modem Connections 141
- Appendix D 143
- CAB0068A 148
- P6 Host port SELV 149
- Adapter Modules 151
- X.21 connections, C-9 162
Produits connexes et manuels pour Routeurs Avaya BayStack ARN Routers
Routeurs Avaya BCM50 Manuel d'utilisateur
(46 pages)
(46 pages)
Routeurs Avaya BCM50 Manuel d'utilisateur
(46 pages)
(46 pages)
Routeurs Avaya 7-10.xx Manuel d'utilisateur
(102 pages)
(102 pages)
Routeurs Avaya Read Me First Router Software 9.00 and Site Manager 3.00 Manuel d'utilisateur
(12 pages)
(12 pages)
Routeurs Avaya V.34 Manuel d'utilisateur
(26 pages)
(26 pages)
Routeurs Avaya BayRS Version 13.10 Avis
(60 pages)
(60 pages)
Routeurs Avaya 4n Avis
(56 pages)
(56 pages)
Routeurs Avaya BCM50 Guide de l'utilisateur
(33 pages)
(33 pages)
Routeurs Avaya BayRS and BCC Software Version 15.4.2.0 Fixed Anomalies Manuel d'utilisateur
(5 pages)
(5 pages)
Routeurs Avaya FE1/E1 Manuel d'utilisateur
(26 pages)
(26 pages)
Routeurs Avaya BCM50 Manuel d'utilisateur
(22 pages)
(22 pages)
© 2020, manymanuals.fr. Tous droits réservés | 4.301 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels