Avaya Configuring WAN Line Services Manuel d'utilisateur Page 281
- Page / 294
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Site Manager WAN Line Services Parameters
117345-B Rev. 00
A-73
Parameter: Pasync Parity Type
Path: COM Connector > Edit Line > AOT > Edit SYNC Parameters
Default: Even
Options: Odd
|
Even
|
High
|
Low
|
None
Function: Sets the error-detection method for isolating altered or damaged AOT packets
during transmission. Asynchronous equipment typically adds a parity bit to the
end of a packet before transmission. This allows the receiving router to detect a
transmission error if it receives a packet with an unexpected parity.
Instructions: Click on Values and select a value that is appropriate for your network: Odd,
Even, High (1), Low (0), or None.
MIB Object ID: 1.3.6.1.4.1.18.3.4.5.1.116
Parameter: Pasync Data Bits
Path: COM Connector > Edit Line > AOT > Edit SYNC Parameters
Default: Eight
Options: Five
|
Six
|
Seven
|
Eight
Function: Sets the length of a polled AOT packet to a specific number of data bits.
Instructions: Click on Values and select a value that is appropriate for your network.
MIB Object ID: 1.3.6.1.4.1.18.3.4.5.1.117
Parameter: Pasync Stop Bits
Path: COM Connector > Edit Line > AOT > Edit SYNC Parameters
Default: Two
Options: One
|
Two
Function: Sets the interval at the end of a transmitted polled AOT packet, allowing the
receiving router to pause before accepting the next packet. More stop bits create
a longer pause at the receiving router.
Instructions: Click on Values and select a value that is appropriate for your network.
MIB Object ID: 1.3.6.1.4.1.18.3.4.5.1.118
- Configuring 1
- WAN Line Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117345-B Rev. 00 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- Bay Networks Customer Service 24
- How to Get Help 24
- Chapter 1 27
- Getting Started 27
- To edit a circuit: 33
- Figure 1-4. Edit Lines Window 34
- Chapter 2 35
- Setting the BofL Timeout 41
- Setting the MTU 41
- Configuring Clocking Signals 43
- Setting the Signal Mode 45
- Setting Minimum Frame Spacing 49
- Setting the CRC Size 52
- Setting the Signaling Method 54
- Setting the Line Coding 55
- Configuring KG84A Security 55
- Setting the Retry Count 59
- Setting the Link Idle Timer 60
- Setting the Cable Type 61
- Setting the Retry Timer 61
- Setting a Priority 62
- Setting the Hold Down Time 63
- Setting the IFTF Pattern 65
- Chapter 3 77
- Asynchronous Services 77
- for information 78
- Setting the Remote IP Address 79
- Specifying the Remote Port 80
- Specifying the Local Port 80
- Setting the Idle Timer 81
- Chapter 4 83
- Setting the Option Mode 85
- Loopback Test Modes 89
- AN/ANH/ARN 90
- Chapter 5 93
- Enabling or Disabling BofL 96
- Using the BCC 100
- Using Site Manager 100
- Configuring HSSI Services 101
- Chapter 6 103
- Editing T1 Services 104
- Setting the T1 Frame Type 105
- Configuring WAN Line Services 106
- Figure 6-2. Bipolar Format 106
- Specifying Line Buildout 107
- Assigning Channel Functions 108
- Editing E1 Services 109
- Enabling or Disabling CRC 111
- Setting the Clock Source 111
- Chapter 7 113
- Setting the Clock Parameters 116
- Configuring a DS0A Connection 129
- Setting Parameters 131
- Table 7-2 132
- Defining Logical Lines 133
- (MCT1 Example) 134
- Circuit Name: MCE1_31_1 135
- Circuit name: MCE1_231_1 135
- (MCE1 Example) 136
- See the following sections: 137
- Caution: 139
- Assigning Timeslots 144
- About the Tests 149
- Setting Port Test Parameters 150
- Running Port Tests 153
- Running Logical Line Tests 158
- Send Command Function 159
- Chapter 8 161
- Configuring FT1 Services 161
- Configuring an FT1 Port 162
- Defining Logical Line 172
- Circuit name: 174
- Chapter 9 189
- Types of Multiline Circuits 190
- Multiline Example 191
- Software Considerations 192
- Logical Lines (MCE1 Example) 205
- Appendix A 209
- Asynchronous Line Parameters 210
- DSU/CSU Parameters 216
- E1 Line Parameters 218
- HSSI Line Parameters 221
- LAPB Parameters 226
- MCE1 Port Parameters 233
- MCT1 Port Parameters 237
- FT1 Port Parameters 252
- FT1 Logical Line Parameters 258
- Synchronous Line Parameters 263
- T1 Line Parameters 282
- Glossary 287
Produits connexes et manuels pour Mise en réseau Avaya Configuring WAN Line Services
(52 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels