Avaya Configuring WAN Line Services Manuel d'utilisateur Page 12
- Page / 294
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
xii
117345-B Rev. 00
Customizing FT1 Port Parameters ......................................................................................... 8-5
Enabling or Disabling the FT1 Port ................................................................................ 8-6
Setting the FT1 Line Type .............................................................................................. 8-6
Setting the FT1 Line Coding ........................................................................................... 8-7
Setting the Signal Level .................................................................................................. 8-7
Setting the Alarm Threshold Time ................................................................................. 8-8
Setting the Alarm Threshold Clear Time ........................................................................ 8-8
Setting the FDL Mode for ESF Line Types .................................................................... 8-9
Setting the Remote FDL HDLC Address Mode ............................................................. 8-9
Accepting or Rejecting Port Loopback Requests ........................................................... 8-9
Setting a Loopback Configuration ................................................................................ 8-10
Setting the Source of Send Performance Messages ...................................................... 8-10
Setting the Source of Accept Performance Messages .................................................. 8-10
Setting the Primary Clock Source ..................................................................................8-11
Setting the Secondary Clock Source ..............................................................................8-11
Configuring a Non-PRI Logical Line ......................................................................................... 8-12
Defining Logical Line ..........................................................................................................8-12
Customizing Logical Line Parameters ................................................................................. 8-14
Enabling or Disabling the Logical Line ........................................................................ 8-16
Enabling or Disabling BofL Messages ......................................................................... 8-16
Setting the BofL Timeout ............................................................................................. 8-17
Enabling or Disabling Logical Line Loopback ............................................................ 8-17
Viewing the Configured WAN Protocol ....................................................................... 8-17
Setting the HDLC Service Type ................................................................................... 8-17
Setting the Local HDLC Address ................................................................................. 8-18
Setting the Remote HDLC Address .............................................................................. 8-18
Setting the CRC Size .................................................................................................... 8-18
Setting the MTU Size ................................................................................................... 8-19
Enabling or Disabling Remote Loopback Detection .................................................... 8-19
Configuring BERT Diagnostic Pattern Tests ................................................................ 8-19
Configuring NRZI Line Encoding ................................................................................ 8-20
Assigning Timeslots ............................................................................................................. 8-21
- Configuring 1
- WAN Line Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117345-B Rev. 00 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- Bay Networks Customer Service 24
- How to Get Help 24
- Chapter 1 27
- Getting Started 27
- To edit a circuit: 33
- Figure 1-4. Edit Lines Window 34
- Chapter 2 35
- Setting the BofL Timeout 41
- Setting the MTU 41
- Configuring Clocking Signals 43
- Setting the Signal Mode 45
- Setting Minimum Frame Spacing 49
- Setting the CRC Size 52
- Setting the Signaling Method 54
- Setting the Line Coding 55
- Configuring KG84A Security 55
- Setting the Retry Count 59
- Setting the Link Idle Timer 60
- Setting the Cable Type 61
- Setting the Retry Timer 61
- Setting a Priority 62
- Setting the Hold Down Time 63
- Setting the IFTF Pattern 65
- Chapter 3 77
- Asynchronous Services 77
- for information 78
- Setting the Remote IP Address 79
- Specifying the Remote Port 80
- Specifying the Local Port 80
- Setting the Idle Timer 81
- Chapter 4 83
- Setting the Option Mode 85
- Loopback Test Modes 89
- AN/ANH/ARN 90
- Chapter 5 93
- Enabling or Disabling BofL 96
- Using the BCC 100
- Using Site Manager 100
- Configuring HSSI Services 101
- Chapter 6 103
- Editing T1 Services 104
- Setting the T1 Frame Type 105
- Configuring WAN Line Services 106
- Figure 6-2. Bipolar Format 106
- Specifying Line Buildout 107
- Assigning Channel Functions 108
- Editing E1 Services 109
- Enabling or Disabling CRC 111
- Setting the Clock Source 111
- Chapter 7 113
- Setting the Clock Parameters 116
- Configuring a DS0A Connection 129
- Setting Parameters 131
- Table 7-2 132
- Defining Logical Lines 133
- (MCT1 Example) 134
- Circuit Name: MCE1_31_1 135
- Circuit name: MCE1_231_1 135
- (MCE1 Example) 136
- See the following sections: 137
- Caution: 139
- Assigning Timeslots 144
- About the Tests 149
- Setting Port Test Parameters 150
- Running Port Tests 153
- Running Logical Line Tests 158
- Send Command Function 159
- Chapter 8 161
- Configuring FT1 Services 161
- Configuring an FT1 Port 162
- Defining Logical Line 172
- Circuit name: 174
- Chapter 9 189
- Types of Multiline Circuits 190
- Multiline Example 191
- Software Considerations 192
- Logical Lines (MCE1 Example) 205
- Appendix A 209
- Asynchronous Line Parameters 210
- DSU/CSU Parameters 216
- E1 Line Parameters 218
- HSSI Line Parameters 221
- LAPB Parameters 226
- MCE1 Port Parameters 233
- MCT1 Port Parameters 237
- FT1 Port Parameters 252
- FT1 Logical Line Parameters 258
- Synchronous Line Parameters 263
- T1 Line Parameters 282
- Glossary 287
Produits connexes et manuels pour Mise en réseau Avaya Configuring WAN Line Services
(52 pages)
(34 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels