Avaya Configuring Frame Relay Services Manuel d'utilisateur Page 65
- Page / 162
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Customizing Frame Relay
117376-B Rev. 00 3-5
Monitoring the Connection
You can monitor the status of your frame relay network connection by setting:
• Time intervals for the router to send messages that verify the integrity of the
link
• The number and frequency of error messages that can occur before the
connection terminates
Polling Interval
The polling interval specifies the interval between status inquiry messages that the
router transmits. Status inquiry messages cause a network response in the form of
a link integrity verification message or full status message. Successful completion
of the request/response “handshake” verifies the status of the router/frame relay
network link. You should accept the default value, 10 seconds. If this value does
not match what the network requests, enter a value that is appropriate for your
network in the range of 5 to 30 seconds. The polling interval does not function if
you set the Management (Mgmnt) Type parameter to DLCMI None.
Full Enquiry Interval
The full enquiry interval specifies the interval between full status inquiry
messages that the router transmits. Full status inquiry messages cause the network
to send a full status report message, which lists all PVCs and their status (active or
inactive, and new or previously established).
The default value, 6, tells the router to send a full status inquiry every 6 polling
intervals. For example, with a polling interval of 10 and a full enquiry interval of
6, the router transmits a full status inquiry every 60 seconds. With a polling
interval of 20 and a full enquiry interval of 30, the router transmits a full status
inquiry every 10 minutes (600 seconds). The full enquiry interval does not
function if you set the Mgmnt Type parameter to DLCMI None.
- Configuring 1
- Frame Relay Services 1
- Contents 5
- Incoming 6
- 117376-B Rev. 00 11
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 22
- Configuring an SVC 23
- Configuring IP Adjacent Hosts 24
- Configuring IPX Adjacent Hosts 25
- 1-6 117376-B Rev. 00 26
- Chapter 2 27
- Frame Relay Overview 27
- Introduction 28
- Permanent Virtual Circuits 29
- Switched Virtual Circuits 29
- PVC and SVC Comparison 30
- Frame Relay Packets 30
- 117376-B Rev. 00 2-5 31
- Management Protocols 32
- Frame Processing 34
- Frame Relay Service Records 34
- Frame Relay Access Modes 35
- Direct Access Mode 36
- Hybrid Access Mode 36
- 2-12 117376-B Rev. 00 38
- Source Routing 39
- RFC 1490 39
- Address Resolution for PVCs 39
- Address Resolution for SVCs 40
- Traffic Control 40
- Data Compression 41
- Data Encryption 42
- Protocol Prioritization 42
- Congestion Control 42
- Traffic Shaping 44
- Quality of Service 45
- 2-20 117376-B Rev. 00 46
- Traffic Shaping for SVCs 47
- 2-22 117376-B Rev. 00 48
- Traffic Shaping Considerations 49
- WCP and CIR Enforcement 50
- Oversubscribing the Interface 51
- 2-26 117376-B Rev. 00 52
- X.213 Priority for SVCs 53
- Inactivity Timing for SVCs 53
- 2-28 117376-B Rev. 00 54
- Multiline for PVCs 55
- 2-30 117376-B Rev. 00 56
- PVC Pass Through 57
- Frame Relay Dial Services 58
- 2-34 117376-B Rev. 00 60
- Chapter 3 61
- Customizing Frame Relay 61
- Selecting a Management Type 62
- Selecting a DLCI Address Type 63
- Selecting Address Length 64
- Monitoring the Connection 65
- 3-6 117376-B Rev. 00 66
- Customizing PVCs 67
- To delete service records: 68
- Enabling Multicast 70
- Configuring PVC Pass Through 72
- 3-14 117376-B Rev. 00 74
- To enable congestion control: 75
- 3-16 117376-B Rev. 00 76
- Enabling Compression for PVCs 77
- 3-18 117376-B Rev. 00 78
- Removing Multiline Services 79
- Customizing SVCs 80
- Adding SVCs 81
- 3-22 117376-B Rev. 00 82
- Disabling SVCs 83
- Disconnecting SVCs 84
- To edit LAPF parameters: 85
- To edit Signaling parameters: 86
- To set X.213 priority values: 88
- 3-30 117376-B Rev. 00 90
- To enable traffic shaping 91
- Enabling Compression for SVCs 92
- To disable compression: 93
- Deleting Frame Relay 95
- Appendix A 97
- A-2 117376-B Rev. 00 98
- 100
- Site Manager Parameters 101
- 102
- 102
- A-8 117376-B Rev. 00 104
- A-10 117376-B Rev. 00 106
- SVC LAPF Parameters 107
- A-12 117376-B Rev. 00 108
- 109
- 110
- A-16 117376-B Rev. 00 112
- SVC Signaling Parameters 113
- A-18 117376-B Rev. 00 114
- A-20 117376-B Rev. 00 116
- Parameters for PVCs 118
- A-24 117376-B Rev. 00 120
- PVC Service Record Parameters 122
- 123
- 123
- A-28 117376-B Rev. 00 124
- 125
- A-30 117376-B Rev. 00 126
- A-32 117376-B Rev. 00 128
- SVC Service Record Parameters 130
- 133
- 134
- SVC Options Parameters 136
- A-46 117376-B Rev. 00 142
- A-48 117376-B Rev. 00 144
- A-50 117376-B Rev. 00 146
- A-52 117376-B Rev. 00 148
- Appendix B 151
- B-2 117376-B Rev. 00 152
- Table B-1. RIP Parameters 152
- B-4 117376-B Rev. 00 154
- B-6 117376-B Rev. 00 156
Produits connexes et manuels pour Mise en réseau Avaya Configuring Frame Relay Services
Mise en réseau Avaya X.25 Manuel d'utilisateur
(148 pages)
(148 pages)
(34 pages)
Mise en réseau Avaya 1D5 Avis
(40 pages)
(40 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels