Avaya Configuring Frame Relay Services Manuel d'utilisateur Page 110
- Page / 162
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring Frame Relay Services
A-14 117376-B Rev. 00
Parameter: Action Initiate
Path: Configuration Manager > Protocols > Interfaces > LAPF
Default: Active
Options: Active
| Passive
Function: Identifies the action LAPF will take to initiate link setup by sending or holding
unnumbered command (SABME) frames to poll the router at the other end of
the connection.
Active indicates that LAPF will send SABME frames and initiate link setup.
Passive indicates that LAPF will hold SABME frames and take no action to
initiate link setup.
To establish a LAPF link, at least one end of the connection has to initiate link
setup.
Instructions: To have LAPF initiate link setup from this router, accept the default, Active, To
have LAPF take no action to initiate link setup, set to Passive.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.9.7.1.7
- Configuring 1
- Frame Relay Services 1
- Contents 5
- Incoming 6
- 117376-B Rev. 00 11
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 22
- Configuring an SVC 23
- Configuring IP Adjacent Hosts 24
- Configuring IPX Adjacent Hosts 25
- 1-6 117376-B Rev. 00 26
- Chapter 2 27
- Frame Relay Overview 27
- Introduction 28
- Permanent Virtual Circuits 29
- Switched Virtual Circuits 29
- PVC and SVC Comparison 30
- Frame Relay Packets 30
- 117376-B Rev. 00 2-5 31
- Management Protocols 32
- Frame Processing 34
- Frame Relay Service Records 34
- Frame Relay Access Modes 35
- Direct Access Mode 36
- Hybrid Access Mode 36
- 2-12 117376-B Rev. 00 38
- Source Routing 39
- RFC 1490 39
- Address Resolution for PVCs 39
- Address Resolution for SVCs 40
- Traffic Control 40
- Data Compression 41
- Data Encryption 42
- Protocol Prioritization 42
- Congestion Control 42
- Traffic Shaping 44
- Quality of Service 45
- 2-20 117376-B Rev. 00 46
- Traffic Shaping for SVCs 47
- 2-22 117376-B Rev. 00 48
- Traffic Shaping Considerations 49
- WCP and CIR Enforcement 50
- Oversubscribing the Interface 51
- 2-26 117376-B Rev. 00 52
- X.213 Priority for SVCs 53
- Inactivity Timing for SVCs 53
- 2-28 117376-B Rev. 00 54
- Multiline for PVCs 55
- 2-30 117376-B Rev. 00 56
- PVC Pass Through 57
- Frame Relay Dial Services 58
- 2-34 117376-B Rev. 00 60
- Chapter 3 61
- Customizing Frame Relay 61
- Selecting a Management Type 62
- Selecting a DLCI Address Type 63
- Selecting Address Length 64
- Monitoring the Connection 65
- 3-6 117376-B Rev. 00 66
- Customizing PVCs 67
- To delete service records: 68
- Enabling Multicast 70
- Configuring PVC Pass Through 72
- 3-14 117376-B Rev. 00 74
- To enable congestion control: 75
- 3-16 117376-B Rev. 00 76
- Enabling Compression for PVCs 77
- 3-18 117376-B Rev. 00 78
- Removing Multiline Services 79
- Customizing SVCs 80
- Adding SVCs 81
- 3-22 117376-B Rev. 00 82
- Disabling SVCs 83
- Disconnecting SVCs 84
- To edit LAPF parameters: 85
- To edit Signaling parameters: 86
- To set X.213 priority values: 88
- 3-30 117376-B Rev. 00 90
- To enable traffic shaping 91
- Enabling Compression for SVCs 92
- To disable compression: 93
- Deleting Frame Relay 95
- Appendix A 97
- A-2 117376-B Rev. 00 98
- 100
- Site Manager Parameters 101
- 102
- 102
- A-8 117376-B Rev. 00 104
- A-10 117376-B Rev. 00 106
- SVC LAPF Parameters 107
- A-12 117376-B Rev. 00 108
- 109
- 110
- A-16 117376-B Rev. 00 112
- SVC Signaling Parameters 113
- A-18 117376-B Rev. 00 114
- A-20 117376-B Rev. 00 116
- Parameters for PVCs 118
- A-24 117376-B Rev. 00 120
- PVC Service Record Parameters 122
- 123
- 123
- A-28 117376-B Rev. 00 124
- 125
- A-30 117376-B Rev. 00 126
- A-32 117376-B Rev. 00 128
- SVC Service Record Parameters 130
- 133
- 134
- SVC Options Parameters 136
- A-46 117376-B Rev. 00 142
- A-48 117376-B Rev. 00 144
- A-50 117376-B Rev. 00 146
- A-52 117376-B Rev. 00 148
- Appendix B 151
- B-2 117376-B Rev. 00 152
- Table B-1. RIP Parameters 152
- B-4 117376-B Rev. 00 154
- B-6 117376-B Rev. 00 156
Produits connexes et manuels pour Mise en réseau Avaya Configuring Frame Relay Services
Mise en réseau Avaya X.25 Manuel d'utilisateur
(148 pages)
(148 pages)
(34 pages)
Mise en réseau Avaya 1D5 Avis
(40 pages)
(40 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels