Avaya Connecting BayStack AN and ANH Platforms to a Network Manuel d'utilisateur Page 87
- Page / 178
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring Network Booting
114074 Rev. A 4-19
Creating the BOOTP Client Interface Table
The upstream router is a booting router’s next-hop router. By default, the booting
router’s synchronous interfaces automatically try to get IP addresses from the
upstream router. This is the EZ-Install process.
If the AN/ANH using EZ-Install gets its address from the upstream router, and the
upstream router’s interface to the AN/ANH is a Frame Relay group access PVC,
you must use Site Manager to connect to the upstream router and create a BOOTP
client interface table (in addition to a BOOTP relay agent forwarding table).
The BOOTP client interface table allows you to specify and pair the IP address of
the AN/ANH with the DLCI of the Frame Relay group access PVC.
For more information about the DLCI and Frame Relay, refer to Configuring
Frame Relay Services.
To create the BOOTP client interface table, begin at the BOOTP Relay Agent
Interface Table window (
refer to Figure 4-6) and proceed as follows:
1. Click on Client I/F.
The BOOTP Client Interface Table window appears
(Figure 4-9).
Note: You do not need to create a BOOTP client interface table if the Frame
Relay PVC is configured to operate in direct access mode, or if the circuit is
configured to operate with the Bay Networks Standard (HDLC encapsulation)
protocol.
Note: If you are using EZ-Install over Frame Relay to boot an AN, you can
have up to 20 PVCs for a single Frame Relay interface on the upstream router.
If you have more than 20 PVCs on the interface where EZ-Install is occurring,
the EZ-Install process may fail. To ensure that the process does not fail,
configure no more than 20 PVCs for a Frame Relay interface.
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- 114074 Rev. A vii 7
- 114074 Rev. A ix 9
- 114074 Rev. A 10
- 114074 Rev. A xi 11
- 114074 Rev. A xiii 13
- About This Guide 15
- Before You Begin 16
- Conventions 17
- Acronyms 18
- 114074 Rev. A xix 19
- 114074 Rev. A xxi 21
- Bay Networks Customer Service 22
- World Wide Web 23
- Customer Service FTP 23
- Support Source CD 24
- CompuServe 24
- InfoFACTS 25
- How to Get Help 25
- Chapter 1 27
- 1-2 114074 Rev. A 28
- ANH Models 29
- 1-4 114074 Rev. A 30
- Access Node Software 31
- Software Management Tools 32
- Router Software 32
- Boot Configuration Options 33
- 1-8 114074 Rev. A 34
- The Boot Process 36
- 114074 Rev. A 1-11 37
- CAN0001A 38
- 114074 Rev. A 1-13 39
- 114074 Rev. A 1-15 41
- Local Boot 42
- CAN0006A 43
- Chapter 2 45
- EZ-Install 46
- Booting the Router Routinely 47
- Directed Netboot 48
- Completing a Startup Option 49
- 114074 Rev. A 2-7 51
- 2-10 114074 Rev. A 54
- Chapter 3 55
- Setting Up a UNIX Boot Server 55
- Setting Up BOOTP Sockets 56
- Setting Up BOOTPD to Run 57
- 3-6 114074 Rev. A 60
- 3-8 114074 Rev. A 62
- Setting Up a TFTP Server 63
- The examples in 64
- 114074 Rev. A 3-11 65
- 3-12 114074 Rev. A 66
- What to Do Next 67
- Chapter 4 69
- Configuring Network Booting 69
- Creating Configuration Files 70
- Preparing an Image 71
- Configuring Network Booting 75
- 4-8 114074 Rev. A 76
- 2. Click on Add 76
- Click on OK 77
- (Figure 4-4) 77
- 79
- 80
- CAN0007A 82
- 114074 Rev. A 4-15 83
- 4-16 114074 Rev. A 84
- 114074 Rev. A 4-17 85
- 4-18 114074 Rev. A 86
- 1. Click on Client I/F 87
- Chapter 5 91
- Network Boot Client 91
- <TFTP host> 92
- (continued) 92
- <TFTP 93
- (continued) 93
- <interface> 94
- <next 94
- <interface> 95
- <IP address> 95
- <subnet mask> 95
- <next hop 95
- 114074 Rev. A 5-8 98
- Chapter 6 99
- 101
- 6-4 114074 Rev. A 102
- 114074 Rev. A 6-5 103
- 6-6 114074 Rev. A 104
- About the N11 DCM 105
- 6-8 114074 Rev. A 106
- Ethernet Statistics Group 107
- Host Group 107
- HostTopN Group 108
- Matrix Group 108
- Filter Group 108
- Packet Capture Group 108
- Enabling the DCM 109
- 111
- 112
- 112
- 113
- 113
- 114
- 114074 Rev. A 6-19 117
- 2. Click on OK 119
- RMON Implementation Notes 121
- RMON Interoperability Issues 121
- 6-24 114074 Rev. A 122
- 114074 Rev. A 6-25 123
- 6-26 114074 Rev. A 124
- 114074 Rev. A 6-27 125
- 6-28 114074 Rev. A 126
- 114074 Rev. A 6-29 127
- Appendix A 129
- Router Fails to Netboot 131
- 114074 Rev. A A-5 133
- <connector> 135
- 114074 Rev. A A-9 137
- Displaying Parameter Settings 138
- 114074 Rev. A A-11 139
- Debugging the BOOTP Server 140
- Table A-1. BOOTP Messages 141
- <IP_address> 143
- Upgrading the Software Image 145
- Restoring a Local File System 145
- Appendix B 147
- Global Information Worksheet 149
- Router Protocol Worksheets 151
- OSPF Worksheet 152
- Wide-Area Protocol Worksheets 154
- Frame Relay Worksheet 155
- PPP Standard Worksheet 156
- CAN0008A 160
- Appendix C 161
- Implementation Notes 161
- C-2 114074 Rev. A 162
- Network Configuration Options 163
- Configuring a Single ANH 164
- 114074 Rev. A C-5 165
- Configuring Multiple Hubs 166
- CAN0010A 167
- C-8 114074 Rev. A 168
- CAN0011A 169
- CAN0012A 170
- 114074 Rev. A Index-1 171
- 114074 Rev. A Index-3 173
- 114074 Rev. A Index-5 175
- 114074 Rev. A Index-7 177
Produits connexes et manuels pour Logiciel Avaya Connecting BayStack AN and ANH Platforms to a Network
Logiciel Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Manuel d'utilisateur
(148 pages)
(148 pages)
Logiciel Avaya Configuring Traffic Filters and Protocol Prioritization Manuel d'utilisateur
(162 pages)
(162 pages)
Logiciel Avaya BCM 4.0 Manuel d'utilisateur
(398 pages)
(398 pages)
Logiciel Avaya Business Communications Manager - Multimedia Contact Center Manuel d'utilisateur
(38 pages)
(38 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels